ae40fd7289
break out tweakable parameters into a separate file
...
this allows for:
include <parameters.scad>
// override a variable such as
frame_z = 60;
include <components.scad>
which will let individual components tweak settings, e.g. the height of
a frame
2023-11-20 14:25:27 -06:00
9a5792580c
add a comment that is all that survived some experimentation
2023-11-16 16:48:05 -06:00
524273369b
correctly refer to the plate overhang as per edge
2023-11-16 09:02:43 -06:00
e7a8fc42ed
correctly refer to the frame wall as per edge
2023-11-16 08:59:06 -06:00
bac99f6ea8
fix dustwashers by scaling them based on the plate hole
2023-11-14 23:56:03 -06:00
53ecd27047
convert decorative plates to scaling the base button rather than adding
2023-11-09 12:47:05 -06:00
d2a1a5be13
scoot the dir arc in and up a bit
...
the horizontal move sends the dir arc closer to the edge, and the
vertical move puts the top back where it used to be before moving the
rest of the layouts down
both of these choices are entirely subjective
2023-11-08 18:38:06 -06:00
56f2214339
scoot the button layouts down a bit
...
this gives a bit more space at the front, mostly so that the decorative
plate doesn't hang over the edge of an inset panel
2023-11-08 18:37:02 -06:00
fbf0dc6896
allow the frame bottom to take insets/raised panels too
...
this complicates the print, in that now printing the frame requires
supports, but by cutting in on the bottom the same way as the top, we
can center some stuff better and also make the plates a bit more
interchangeable. this also eliminates the slightly unsightly bottom
panel hanging out in the open, so overall I think it's worth the
printing complication
2023-11-02 16:34:08 -05:00
8025038db5
improve 24mm + W layout components, add decorative plate
2023-10-04 16:47:06 -05:00
4ec97b9f36
add components for an OLED cutout and panel using it
2023-10-04 16:44:59 -05:00
2aab029905
use the same frame cutout for neutrik D and 24mm holes
2023-09-11 20:34:09 -05:00
3f0712af70
try making the frame wider than it is deep
...
the goal is to try to fit a hitstick-w into two frames
2023-09-11 13:29:40 -05:00
47d9a523c3
remove double translation of dir_arc-30mm layouts
2023-09-11 11:43:25 -05:00
cfb48574b2
change 30mm dir_arc layouts to be based on the thumb position
...
this will hopefully make some moving of stuff around a bit easier
2023-09-11 11:25:59 -05:00
86ba641ba6
modularize the directional arc part of the 24mm all buttons layout
...
this was for a failed experiment, but it's probably good to do this
regardless
2023-09-11 10:37:43 -05:00
3d24dad1ae
spread out the frame connection holes a bit
2023-09-11 09:56:52 -05:00
fe961e8a7e
make neutrik D cutout bigger, simplifies that frame wall
2023-09-11 09:45:09 -05:00
28c0c0e475
properly and relatively position neutrik cutouts
2023-09-11 09:33:39 -05:00
2960151d98
remove more magic numbers, overhang relative to base frame stuff
2023-09-08 14:08:40 -05:00
82d1913551
remove more magic numbers, top plate is a derivative of base frame dimensions
2023-09-08 13:53:51 -05:00
88fc53988e
remove some magic numbers that are derived from base dimensions
2023-09-08 13:44:05 -05:00
f73c94be2f
move the rotated top plate into something reusable
2023-09-08 13:17:04 -05:00
7a71c8cd81
simple naming consistency change
...
sed -i 's/topplate_with_raised/top_plate_with_raised/' **/*.scad
2023-09-08 12:22:53 -05:00
350fc27285
break up the sega 2P layout into parts
...
messing with something that may never see the light of day, but no harm
in doing this
2023-09-08 12:15:46 -05:00
e68ffbfc7b
decorative button surround plates for the top
2023-09-03 09:53:49 -05:00
43a036e17c
consolidate button hole and wider cylinder into one object
...
nothing was materially using the non-snap-in cutout anymore (except for
the frame which wasn't updated since removing the bigger cutout
rectangle, so I fixed that), and I want to use it for a template thing
I'm working on, so remove some cruft
2023-08-30 10:02:12 -05:00
3b964ee6d8
scoot the buttons in panels a bit closer to each other
2023-08-30 00:24:19 -05:00
fe0e3b6017
center the button panels and their layouts
...
I can refactor the double translation away at soem later point
2023-08-30 00:22:31 -05:00
cd5cd422e5
rename side chopper, going to be used for more than just frames
2023-08-29 10:13:40 -05:00
73e93d4536
make a bottom overhang plate
...
slightly different than the top since there's no inset, so no need for
that frame or the posts
2023-08-29 10:06:21 -05:00
e51b79a193
squeeze dir. arc + W w/8 buttons on one panel
...
it's a tight squeeze; fits in the frame, but frame buttons/quick
connects maybe a problem
2023-08-28 10:51:07 -05:00
694e2c6173
bring 5 mm back to the frame
...
to accommodate quick connects, levers, etc.
2023-08-28 10:47:53 -05:00
a8ca6bafa9
fix the frame support box again
...
math is even harder when you're not using the right variables
2023-08-28 00:08:48 -05:00
cd71ed013b
fix the frame box width, which was too thin bc math is hard
2023-08-27 15:17:24 -05:00
12273649f5
better name for the 24mm dir + 6 button panel
2023-08-27 14:36:34 -05:00
344de2c84f
standalone frame, with tweaks to the frame as a consequence
...
* frame width has been reduced in order to leave more space and have
sunken buttons somewhat accessible
* the cutout for neutrik mounts has been reduced and moved into the
holes themselves, to do this more modularly and restore some support
2023-08-26 21:57:12 -05:00
a8d02f9229
squish a decent all buttons layout onto one panel
...
this uses the new raised panel look, I'm trying it out but haven't
updated the other top panels yet until I'm sure I like it --- it'll mean
a lot of chopping
2023-08-26 14:48:01 -05:00
af38f0a580
move top plate holes into reusable module
2023-08-26 14:42:58 -05:00
19fa31b425
a one-panel 24mm dir arc + action buttons layout
...
(you can fit 6! not bad!)
2023-08-25 15:36:41 -05:00
6ca57615e4
solve for 24mm/30mm snap-ins
2023-08-25 15:36:38 -05:00
9f98f0cfa7
rename project before sharing
2023-08-24 22:49:34 -05:00
00e8344a91
panel for 30mm "directional arc" buttons + W + one extra
...
the extra could be mapped to L3 or soemthing like that, for SF6 or other
weirdos
2023-08-21 15:00:28 -05:00
facee903cf
add mount for a standard PS360+/RP2040ABB form factor PCB
2023-08-20 23:59:24 -05:00
f5ecdc9154
shrink the JLF mount panel height by 1mm
...
trying to shave a couple mm off the design to make room for this Seimitsu SEL-70X-F
2023-08-20 23:54:50 -05:00
33271abef0
leaving some notes and comments for myself
2023-08-20 09:56:02 -05:00
6064884a89
account for 24mm buttons in the frame tops
2023-08-19 17:51:01 -05:00
7faa28b4b1
simplify the frame and use roundedcube for it
2023-08-19 08:59:41 -05:00
6c04c1b2f2
ethercon (and probably other neutrik Ds) need the wall thinner
...
to avoid overhang, this shrinks the overall case by 2mm on the x and y,
as this number was somewhat arbitrary
2023-08-18 13:18:38 -05:00
42f417d86a
middle frame mostly ok, but I forgot to check neutrik panel thickness
2023-08-18 00:23:59 -05:00
