fbf0dc6896
allow the frame bottom to take insets/raised panels too
...
this complicates the print, in that now printing the frame requires
supports, but by cutting in on the bottom the same way as the top, we
can center some stuff better and also make the plates a bit more
interchangeable. this also eliminates the slightly unsightly bottom
panel hanging out in the open, so overall I think it's worth the
printing complication
2023-11-02 16:34:08 -05:00
538fb1430b
add a dustwasher for JLF mounts
2023-10-26 18:09:41 -05:00
8025038db5
improve 24mm + W layout components, add decorative plate
2023-10-04 16:47:06 -05:00
11107fe826
add lever + 6 30mm button sega 2P layout panel
...
a bit tight but totally possible
2023-10-04 16:45:53 -05:00
4ec97b9f36
add components for an OLED cutout and panel using it
2023-10-04 16:44:59 -05:00
a960e57bd1
docs updates for v3
2023-09-17 11:33:49 -05:00
c67722d0da
simple button outline for a single 24mm button
2023-09-17 11:29:31 -05:00
fa1f6927c5
new demo for v3 --- two panels
2023-09-17 11:28:56 -05:00
1da14d6dc3
remove stuff taken care of, bump engraving down again
2023-09-15 15:32:24 -05:00
0611e23975
keep some notes on filament while I'm at it
2023-09-15 15:30:10 -05:00
87db45df15
complete the cost estimation: total ~$26 for an enclosure
2023-09-15 15:20:17 -05:00
28809230bc
sega 2p panel with a button for start or whatever
2023-09-15 15:03:49 -05:00
2253889430
remove unnecessary difference/union duplication
2023-09-15 15:01:39 -05:00
a26f87a9d2
fit an arcade layout in one panel
2023-09-13 21:17:45 -05:00
962402c291
new top panels for my current two-frame experiment
...
seems good so far
2023-09-13 20:46:00 -05:00
63c7113d9f
more notes for next time
2023-09-12 23:52:32 -05:00
163dfc2c63
commit my new target assembly
2023-09-12 23:51:37 -05:00
aa633584e5
don't mirror, mostly duplicate the left frame components into right frame
...
doing a naive mirror meant the neutrik D mount holes were in the wrong
spot. fine for a 20mm + plate mount, but not good for any actual
component
2023-09-12 23:40:51 -05:00
767b38acef
more TODO notes
2023-09-12 23:40:48 -05:00
56367369b7
more panel estimates
2023-09-12 20:19:43 -05:00
fa304606df
generalize the top panel cost, they should all come in around this
2023-09-12 17:09:30 -05:00
5d5eb34f8a
top panel cost for something like the lever + dir_arc panel
2023-09-12 13:03:35 -05:00
17ab4815a6
more cost estimate documentation
2023-09-12 10:36:15 -05:00
afd548f8d9
correct hardware notes, since v2 the M4 standoffs are 45mm
2023-09-12 10:14:45 -05:00
e2549694ea
start estimating cost of build
2023-09-12 09:24:33 -05:00
2aab029905
use the same frame cutout for neutrik D and 24mm holes
2023-09-11 20:34:09 -05:00
0f11aacec4
un-rotate the solo frame now that X is longer
2023-09-11 20:28:33 -05:00
3f0712af70
try making the frame wider than it is deep
...
the goal is to try to fit a hitstick-w into two frames
2023-09-11 13:29:40 -05:00
51ba220a5a
refer to proper parent filename
2023-09-11 12:01:27 -05:00
47d9a523c3
remove double translation of dir_arc-30mm layouts
2023-09-11 11:43:25 -05:00
3e74f3d915
refer to proper parent filename
2023-09-11 11:28:18 -05:00
cfb48574b2
change 30mm dir_arc layouts to be based on the thumb position
...
this will hopefully make some moving of stuff around a bit easier
2023-09-11 11:25:59 -05:00
36a96fbe26
tighten up the inner hole a bit, to no noticeable detriment
2023-09-11 10:37:46 -05:00
86ba641ba6
modularize the directional arc part of the 24mm all buttons layout
...
this was for a failed experiment, but it's probably good to do this
regardless
2023-09-11 10:37:43 -05:00
3d24dad1ae
spread out the frame connection holes a bit
2023-09-11 09:56:52 -05:00
fe961e8a7e
make neutrik D cutout bigger, simplifies that frame wall
2023-09-11 09:45:09 -05:00
28c0c0e475
properly and relatively position neutrik cutouts
2023-09-11 09:33:39 -05:00
2960151d98
remove more magic numbers, overhang relative to base frame stuff
2023-09-08 14:08:40 -05:00
82d1913551
remove more magic numbers, top plate is a derivative of base frame dimensions
2023-09-08 13:53:51 -05:00
88fc53988e
remove some magic numbers that are derived from base dimensions
2023-09-08 13:44:05 -05:00
f73c94be2f
move the rotated top plate into something reusable
2023-09-08 13:17:04 -05:00
cd21b4dd0a
remove unused import
2023-09-08 13:14:53 -05:00
7a71c8cd81
simple naming consistency change
...
sed -i 's/topplate_with_raised/top_plate_with_raised/' **/*.scad
2023-09-08 12:22:53 -05:00
350fc27285
break up the sega 2P layout into parts
...
messing with something that may never see the light of day, but no harm
in doing this
2023-09-08 12:15:46 -05:00
3b3b857568
build improvements, create zip file
2023-09-07 19:53:56 -05:00
fddb5d450e
commit my scratch file since it's a good demo
2023-09-07 19:17:48 -05:00
0329dd2b3c
make dustwasher hole a bit bigger to let the lever move
2023-09-07 19:12:20 -05:00
ee3dd23b36
another idea for next time
2023-09-07 11:02:00 -05:00
0e00f8d5d1
with the frame redesign, we can use 16mm M4s
2023-09-07 00:19:42 -05:00
b911a1b7c1
three section v2 render
2023-09-06 16:24:58 -05:00
