new decorative plate for the 3-button aux controls

this is a bit cleaner/DRY, and also lets me experiment with a decorative
plate easily

README.md

@@ -36,12 +36,12 @@ What you'll need beyond these objects:
   Board](https://github.com/OpenStickCommunity/Hardware/tree/main/RP2040%20Advanced%20Breakout%20Board))
     * 4 M3 8mm hex bolts to secure the PCB to a panel
 * Per frame and plate combo:
-    * 4 40mm M4 hex brass standoffs (or equivalent)
+    * 4 45mm M4 hex brass standoffs (or equivalent)
     * 8 M4 countersunk hex bolts
         * Overhang plates should use 12-16mm length bolts since they are taller
         * Inset plates should probably use 8-12mm bolts --- some standoffs aren't threaded the whole way, making 16mm
           too long to go flush
-        * If making the 40mm standoffs from multiple smaller ones, make sure they have enough length to take your bolts!
+        * If making the 45mm standoffs from multiple smaller ones, make sure they have enough length to take your bolts!
 * Per frame connection point:
     * 8 16mm M4 bolts
     * 8 M4 flange nuts
@@ -69,7 +69,7 @@ Filament masses from Bambu Studio estimates, using Bambu PLA Basic.
   of 2023-09-12)
 * 4 M3 flange nuts to connect Neutrik D plates to frames: **$0.34 USD** (you can get a pack of 100 on Amazon for $8.50,
   as of 2023-09-12)
-* 8 40mm M4 spacers to connect panels to frames: **$2.40 USD** (you can get a pack of 10 on AliExpress for $3, as of
+* 8 45mm M4 spacers to connect panels to frames: **$2.40 USD** (you can get a pack of 10 on AliExpress for $3, as of
   2023-09-12)
     * You could 3D print these too, but you're probably better off with brass ones as they give some weight to the
       stick anyway

docs/materials.md

@@ -21,4 +21,5 @@ bss's random thoughts and notes on 3D printing materials.
 
 ## Hatchbox PLA
 
-* Haven't done a lot of this yet, but my wife really likes the blue.
+* **Blue:** very blue. Wife likes it.
+* **White:** more opaque than the Bambu PLA mentioned above, makes a pretty decent (still slightly translucent) frame.

src/blown-up-demo.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <frame-left.scad>
 use <frame-right.scad>

src/bottom-panel-inset.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module bottom_panel() {

src/bottom-panel-left.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <bottom-panel-solo.scad>
 

src/bottom-panel-middle.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <bottom-panel-left.scad>
 use <bottom-panel-right.scad>

src/bottom-panel-right.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <bottom-panel-left.scad>
 

src/bottom-panel-solo.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module bottom_panel_solo() {

src/components.scad

@@ -18,75 +18,6 @@
 
 include <roundedcube.scad>
 
-/* QUASI-CONSTANTS */
-
-// adjustments
-hole_tolerance = 0.15;
-
-// M2
-m2_screw_selftap_radius = 0.95;
-
-// M3
-m3_screw_selftap_radius = 1.3;
-
-// M4
-m4_bolt_radius = 2 + hole_tolerance;
-m4_bolt_countersink_radius = 6.1 + hole_tolerance;
-m4_bolt_hex_exterior_radius = 3.6 + hole_tolerance;
-
-// 24mm button
-small_button_radius = 12 + hole_tolerance;
-
-// 30mm button
-big_button_radius = 15 + hole_tolerance;
-
-// JLF mount dimensions
-lever_mount_x = 53;
-lever_mount_y = 95;
-lever_mount_z = 2;
-
-// standard lever hole
-lever_plate_hole = 12;
-
-// case dimensions
-// base frame box. reminder: top of inside (including mounts) is chopped by top_plate_z for plates
-frame_x = 233;
-frame_y = 208;
-frame_z = 50;
-
-// depth of the "lip" of the frame that the top plate sets into/supports the overhang
-frame_wall = 4;
-
-// per neutrik (mm)
-neutrik_panel_thickness = 3;
-
-// top plate, which can either be the whole plate ("inset") or the mounting frame for a plate that overhangs
-top_plate_x = frame_x - (frame_wall * 2);
-top_plate_y = frame_y - (frame_wall * 2);
-top_plate_z = 5;
-
-// how much the top plate x/y is expanded to overhang the frame
-// note that this is relative to the top plate (so the wall is added back)
-top_plate_overhang_amount = 8.5;
-overhang_top_plate_x = top_plate_x + (frame_wall * 2) + (top_plate_overhang_amount * 2);
-overhang_top_plate_y = top_plate_y + (frame_wall * 2) + (top_plate_overhang_amount * 2);
-
-plate_to_frame_point_x = (top_plate_x/2)-10;
-plate_to_frame_point_y = (top_plate_y/2)-10;
-
-// frame interior that supports the top plates
-panel_support_width = 5;
-
-// neutrik D screw holes
-neutrik_d_screw_radius = 1.6 + hole_tolerance;
-neutrik_d_radius = 12 + hole_tolerance;
-
-// additional button radius for decorative panels, etc.
-decorative_radius_scale = 1.75;
-jumbo_decorative_radius_scale = 2;
-
-/* PARTS */
-
 module m4_hole() {
 	cylinder(r=m4_bolt_radius, h=100, $fn=50, center=true);
 }
@@ -156,9 +87,16 @@ module neutrik_d_mount() {
 	translate([-9.5, -12, 0]) neutrik_d_screw_hole();
 }
 
-// space for a neutrik D mount or 24mm button
+// space for a neutrik D mount or 24mm button - Z is to cut the whole inside without affecting panel lip
 module frame_cutout() {
-	cube([36.5, 8, 40], center=true);
+	cube([36.5, 8, frame_z-(top_plate_z*2)], center=true);
+}
+
+// bank of three 24mm buttons, commonly on a frame face
+module aux_control_three_button_cluster() {
+	translate([-40, 0, 0]) button_24mm_hole();
+	translate([0, 0, 0]) button_24mm_hole();
+	translate([40, 0, 0]) button_24mm_hole();
 }
 
 module m2_mount_post() {

src/frame-left.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module base_left_frame() {
@@ -36,11 +37,9 @@ module left_frame() {
 		frame_cable_routing_hole();
 
 		// aux button holes
-		translate([-30, 101.5, 0]) rotate([270, 0, 0]) button_24mm_hole();
+		translate([-30, 101.5, 0]) rotate([270, 0, 0]) aux_control_three_button_cluster();
 		translate([-30, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([-70, 101.5, 0]) rotate([270, 0, 0]) button_24mm_hole();
 		translate([-70, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([10, 101.5, 0]) rotate([270, 0, 0]) button_24mm_hole();
 		translate([10, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
 
 		// neutrix button hole

src/frame-middle.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module base_middle_frame() {

src/frame-right.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module base_right_frame() {
@@ -36,11 +37,9 @@ module right_frame() {
 		mirror([1, 0, 0]) frame_cable_routing_hole();
 
 		// aux button holes
-		translate([30, 101.5, 0]) rotate([270, 0, 0]) button_24mm_hole();
+		translate([30, 101.5, 0]) rotate([270, 0, 0]) aux_control_three_button_cluster();
 		translate([30, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([70, 101.5, 0]) rotate([270, 0, 0]) button_24mm_hole();
 		translate([70, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([-10, 101.5, 0]) rotate([270, 0, 0]) button_24mm_hole();
 		translate([-10, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
 
 		// neutrix button hole

src/frame-solo.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module solo_frame() {
@@ -31,23 +32,14 @@ module solo_frame() {
 		translate([40, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
 
 		// aux button holes
-		translate([-frame_x/2+2.5, 0, 0]) rotate([0, 0, 270])
+		translate([-frame_x/2+2.5, 0, 0]) rotate([90, 0, 270]) aux_control_three_button_cluster();
-			translate([0, 0, 0]) rotate([90, 0, 0]) button_24mm_hole();
 		translate([(frame_x/2)-neutrik_panel_thickness-4, 0, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([-frame_x/2+2.5, 0, 0]) rotate([0, 0, 270])
-			translate([-40, 0, 0]) rotate([90, 0, 0]) button_24mm_hole();
 		translate([(frame_x/2)-neutrik_panel_thickness-4, -40, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([-frame_x/2+2.5, 0, 0]) rotate([0, 0, 270])
-			translate([40, 0, 0]) rotate([90, 0, 0]) button_24mm_hole();
 		translate([(frame_x/2)-neutrik_panel_thickness-4, 40, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([frame_x/2-2.5, 0, 0]) rotate([0, 0, 90])
+
-			translate([0, 0, 0]) rotate([90, 0, 0]) button_24mm_hole();
+		translate([frame_x/2+2.5, 0, 0]) rotate([90, 0, 270]) aux_control_three_button_cluster();
 		translate([-(frame_x/2)+neutrik_panel_thickness+4, 0, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([frame_x/2-2.5, 0, 0]) rotate([0, 0, 90])
-			translate([-40, 0, 0]) rotate([90, 0, 0]) button_24mm_hole();
 		translate([-(frame_x/2)+neutrik_panel_thickness+4, -40, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([frame_x/2-2.5, 0, 0]) rotate([0, 0, 90])
-			translate([40, 0, 0]) rotate([90, 0, 0]) button_24mm_hole();
 		translate([-(frame_x/2)+neutrik_panel_thickness+4, 40, 0]) rotate([0, 0, 90]) frame_cutout();
 	}
 }

src/misc-decorative-plate-24mm-button.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module button_24mm_decorative_plate() {

src/misc-decorative-plate-aux-control-three-button-cluster.scad

@@ -0,0 +1,33 @@
+/* Copyright Brian Stephan 2023
+ *
+ * This file is part of the Buildable Stick System.
+ *
+ * The Buildable Stick System is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the
+ * Free Software Foundation, either version 3 of the License, or (at your
+ * option) any later version.
+ *
+ * The Buildable Stick System is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
+ * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <misc-neutrik-d-plate.scad>
+
+module aux_control_three_button_cluster_decorative_plate() {
+	difference() {
+		hull() {
+			translate([-50, 0, 0]) neutrik_d_plate();
+			translate([50, 0, 0]) neutrik_d_plate();
+		}
+		translate([0, 0, -10]) aux_control_three_button_cluster();
+	}
+}
+
+aux_control_three_button_cluster_decorative_plate();

src/misc-decorative-plate-dir_arc-plus-w-24mm-8-button.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module dir_arc_plus_w_24mm_8_button_decorative_plate() {

src/misc-decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-plus-one.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate() {

src/misc-decorative-plate-dir_arc-plus-w-30mm.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module dir_arc_plus_w_30mm_decorative_plate() {

src/misc-decorative-plate-sega-2p-6-button.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module sega_2p_6_button_decorative_plate() {

src/misc-decorative-plate-sega-2p-plus-one.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module sega_2p_plus_one_decorative_plate() {

src/misc-dustwasher-jlf.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module jlf_dustwasher() {

src/misc-dustwasher-lsx-nobi.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module lsx_nobi_dustwasher() {

src/misc-neutrik-d-plate-20mm-hole.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <misc-neutrik-d-plate.scad>
 

src/misc-neutrik-d-plate-24mm-hole.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <misc-neutrik-d-plate.scad>
 

src/misc-neutrik-d-plate.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module neutrik_d_plate() {

src/parameters.scad

@@ -0,0 +1,82 @@
+/* Copyright Brian Stephan 2023
+ *
+ * This file is part of the Buildable Stick System.
+ *
+ * The Buildable Stick System is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by the
+ * Free Software Foundation, either version 3 of the License, or (at your
+ * option) any later version.
+ *
+ * The Buildable Stick System is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
+ * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
+ */
+
+// adjustments
+hole_tolerance = 0.15;
+
+// M2
+m2_screw_selftap_radius = 0.95;
+
+// M3
+m3_screw_selftap_radius = 1.3;
+
+// M4
+m4_bolt_radius = 2 + hole_tolerance;
+m4_bolt_countersink_radius = 6.1 + hole_tolerance;
+m4_bolt_hex_exterior_radius = 3.6 + hole_tolerance;
+
+// 24mm button
+small_button_radius = 12 + hole_tolerance;
+
+// 30mm button
+big_button_radius = 15 + hole_tolerance;
+
+// JLF mount dimensions
+lever_mount_x = 53;
+lever_mount_y = 95;
+lever_mount_z = 2;
+
+// standard lever hole
+lever_plate_hole = 12;
+
+// case dimensions
+// base frame box. reminder: top of inside (including mounts) is chopped by top_plate_z for plates
+frame_x = 233;
+frame_y = 208;
+frame_z = 55;
+
+// depth of the "lip" of the frame that the top plate sets into/supports the overhang
+frame_wall = 4;
+
+// per neutrik (mm)
+neutrik_panel_thickness = 3;
+
+// top plate, which can either be the whole plate ("inset") or the mounting frame for a plate that overhangs
+top_plate_x = frame_x - (frame_wall * 2);
+top_plate_y = frame_y - (frame_wall * 2);
+top_plate_z = 5;
+
+// how much the top plate x/y is expanded to overhang the frame
+// note that this is relative to the top plate (so the wall is added back)
+top_plate_overhang_amount = 8.5;
+overhang_top_plate_x = top_plate_x + (frame_wall * 2) + (top_plate_overhang_amount * 2);
+overhang_top_plate_y = top_plate_y + (frame_wall * 2) + (top_plate_overhang_amount * 2);
+
+plate_to_frame_point_x = (top_plate_x/2)-10;
+plate_to_frame_point_y = (top_plate_y/2)-10;
+
+// frame interior that supports the top plates
+panel_support_width = 5;
+
+// neutrik D screw holes
+neutrik_d_screw_radius = 1.6 + hole_tolerance;
+neutrik_d_radius = 12 + hole_tolerance;
+
+// additional button radius for decorative panels, etc.
+decorative_radius_scale = 1.75;
+jumbo_decorative_radius_scale = 2;

src/top-panel-inset-dir_arc-plus-w-30mm-plus-one-with-mount.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <top-panel-inset-dir_arc-plus-w-30mm-plus-one.scad>
 

src/top-panel-inset-dir_arc-plus-w-30mm-plus-one.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module dir_arc_w_30mm_plus_one_panel() {

src/top-panel-inset-lever-and-dir_arc-plus-w-30mm.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module top_panel_inset_lever_and_dir_arc_w_30mm() {

src/top-panel-inset-lever-with-mount.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <top-panel-inset-lever.scad>
 

src/top-panel-inset-lever.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 // combine the lever mount and generic plate, with mounting holes

src/top-panel-inset-namco-noir-plus-one.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module namco_noir_plus_one_panel() {

src/top-panel-inset-namco-noir-plus-two.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module namco_noir_plus_two_panel() {

src/top-panel-inset-sega-2p-plus-one-plus-control-with-mount.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <top-panel-inset-sega-2p-plus-one-plus-control.scad>
 

src/top-panel-inset-sega-2p-plus-one-plus-control.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module top_panel_inset_sega_2p_plus_one_plus_control() {

src/top-panel-inset-sega-2p-plus-one.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module sega_2p_plus_one_panel() {

src/top-panel-left-lever-and-dir_arc-plus-w-30mm.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module top_panel_left_lever_and_dir_arc_w_30mm() {

src/top-panel-left-lever.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 // combine the lever mount and generic plate, with mounting holes

src/top-panel-middle-dir_arc-plus-w-30mm-with-mount.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <top-panel-middle-dir_arc-plus-w-30mm.scad>
 

src/top-panel-middle-dir_arc-plus-w-30mm.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module top_panel_middle_dir_arc_w_30mm() {

src/top-panel-right-sega-2p-plus-one-plus-control-with-mount-with-oled.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <top-panel-right-sega-2p-plus-one-plus-control-with-mount.scad>
 

src/top-panel-right-sega-2p-plus-one-plus-control-with-mount.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <top-panel-right-sega-2p-plus-one-plus-control.scad>
 

src/top-panel-right-sega-2p-plus-one-plus-control.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module top_panel_right_sega_2p_plus_one_plus_control() {

src/top-panel-right-sega-2p-plus-one-with-mount.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 use <top-panel-right-sega-2p-plus-one.scad>
 

src/top-panel-right-sega-2p-plus-one.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module top_panel_right_sega_2p_plus_one() {

src/top-panel-solo-dir_arc-24mm-6-button.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module dir_arc_24mm_6_button_panel() {

src/top-panel-solo-dir_arc-plus-w-24mm-8-button.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module dir_arc_plus_w_24mm_8_button_panel() {

src/top-panel-solo-lever-and-sega-2p-6-button.scad

@@ -16,6 +16,7 @@
  * the Buildable Stick System. If not, see <https://www.gnu.org/licenses/>.
  */
 
+include <parameters.scad>
 include <components.scad>
 
 module top_panel_solo_lever_and_sega_2p_6_button() {