src/components.scad

@@ -31,9 +31,9 @@ module panel_holes() {
 module button_24mm_hole() {
 	cylinder(r=small_button_radius, h=100, $fn=50, center=true);
 	// carve out space for snap-ins, leave 3mm
-	// slagcoin has screw-in nut diameter at 29.5mm, so radius+3 to leave some space
+	// slagcoin has screw-in nut diameter at 29.5mm, so radius+6 to leave some space
 	// translation is to leave 3mm thickness in the plate without recentering anything
-	translate([0, 0, -25]) cylinder(r=small_button_radius+3, h=49, $fn=50, center=true);
+	translate([0, 0, -25]) cylinder(r=small_button_radius+6, h=49, $fn=50, center=true);
 	// space for decorative button surround stuff
 	translate([0, 0, 50]) cylinder(r=small_button_radius*decorative_radius_scale, h=20, $fn=50, center=true);
 	translate([0, 0, 70]) cylinder(r=small_button_radius*jumbo_decorative_radius_scale, h=20, $fn=50, center=true);
@@ -83,14 +83,14 @@ module rocker_20mm_mount() {
 
 // space for a neutrik D mount or 24mm button - Z is to cut the whole inside without affecting panel lip
 module frame_cutout() {
-	cube([30.5, 8, frame_z-(panel_z*2)], center=true);
+	cube([36.5, 8, frame_z-(panel_z*2)], center=true);
 }
 
 // bank of three 24mm buttons, commonly on a frame face
 module aux_control_three_button_cluster() {
-	translate([-37, 0, 0]) button_24mm_hole();
+	translate([-40, 0, 0]) button_24mm_hole();
 	translate([0, 0, 0]) button_24mm_hole();
-	translate([37, 0, 0]) button_24mm_hole();
+	translate([40, 0, 0]) button_24mm_hole();
 }
 
 module m2_mount_post() {
@@ -163,32 +163,15 @@ module levermountholes() {
 }
 
 module base_panel() {
-	difference() {
+	cube([panel_x, panel_y, panel_z], center=true);
-		union() {
+	translate([panel_to_frame_point_x, panel_to_frame_point_y, -panel_z])
-			cube([panel_x, panel_y, panel_z], center=true);
+		scale([1.4, 1.4, 0.1]) frame_hex_bolt_hole();
-			// add posts that sink into the frame, just to give
+	translate([-panel_to_frame_point_x, panel_to_frame_point_y, -panel_z])
-			// a somewhat more sturdy/tight connection
+		scale([1.4, 1.4, 0.1]) frame_hex_bolt_hole();
-			translate([panel_to_frame_point_x, panel_to_frame_point_y, -panel_z])
+	translate([panel_to_frame_point_x, -panel_to_frame_point_y, -panel_z])
-				scale([1.5, 1.5, 0.1]) frame_hex_bolt_hole();
+		scale([1.4, 1.4, 0.1]) frame_hex_bolt_hole();
-			translate([-panel_to_frame_point_x, panel_to_frame_point_y, -panel_z])
+	translate([-panel_to_frame_point_x, -panel_to_frame_point_y, -panel_z])
-				scale([1.5, 1.5, 0.1]) frame_hex_bolt_hole();
+		scale([1.4, 1.4, 0.1]) frame_hex_bolt_hole();
-			translate([panel_to_frame_point_x, -panel_to_frame_point_y, -panel_z])
-				scale([1.5, 1.5, 0.1]) frame_hex_bolt_hole();
-			translate([-panel_to_frame_point_x, -panel_to_frame_point_y, -panel_z])
-				scale([1.5, 1.5, 0.1]) frame_hex_bolt_hole();
-		}
-		// the posts mentioned above need space for the actual hex bolts
-		// used in connecting to the frame
-		translate([panel_to_frame_point_x, panel_to_frame_point_y, -panel_z])
-			scale([1, 1, 0.1]) frame_hex_bolt_hole();
-		translate([-panel_to_frame_point_x, panel_to_frame_point_y, -panel_z])
-			scale([1, 1, 0.1]) frame_hex_bolt_hole();
-		translate([panel_to_frame_point_x, -panel_to_frame_point_y, -panel_z])
-			scale([1, 1, 0.1]) frame_hex_bolt_hole();
-		translate([-panel_to_frame_point_x, -panel_to_frame_point_y, -panel_z])
-			scale([1, 1, 0.1]) frame_hex_bolt_hole();
-	}
-
 }
 
 module base_bottom_panel() {
@@ -240,16 +223,11 @@ module panel_with_raised_overhang() {
 
 module frame_box() {
 	difference() {
-		top_points = [
+		points = [ [(frame_x/2)-3, (frame_y/2)-3, 0], [-(frame_x/2)+3, (frame_y/2)-3, 0],
-			// top part, majority of shape
+			[(frame_x/2)-3, -(frame_y/2)+3, 0], [-(frame_x/2)+3, -(frame_y/2)+3, 0] ];
-			[(frame_x/2)-3, (frame_y/2)-3, panel_z/2],
-			[-(frame_x/2)+3, (frame_y/2)-3, panel_z/2],
-			[(frame_x/2)-3, -(frame_y/2)+3, panel_z/2],
-			[-(frame_x/2)+3, -(frame_y/2)+3, panel_z/2],
-		];
 		hull() {
-			for (p = top_points) {
+			for (p = points) {
-				translate(p) cylinder(r=3, h=frame_z-panel_z, center=true);
+				translate(p) cylinder(r=3, h=frame_z, center=true);
 			}
 		}
 		// cut out the middle to make it a box
@@ -304,9 +282,6 @@ module frame() {
 		translate([-panel_to_frame_point_x, -panel_to_frame_point_y, 0]) frame_hex_bolt_hole();
 
 		// comfort bevel
-		translate([frame_x/2, 0, frame_z/2]) rotate([0, 45, 0]) cube([4, frame_y+0.01, 4], center=true);
-		translate([-frame_x/2, 0, frame_z/2]) rotate([0, 45, 0]) cube([4, frame_y+0.01, 4], center=true);
-		translate([0, frame_y/2, frame_z/2]) rotate([45, 0, 0]) cube([frame_x+0.01, 4, 4], center=true);
 		translate([0, -frame_y/2, frame_z/2]) rotate([45, 0, 0]) cube([frame_x+0.01, 4, 4], center=true);
 
 		// slightly larger holes than the posts in the base_panel

src/frame-left.scad

@@ -24,13 +24,13 @@ module left_frame() {
 		frame_cable_routing_hole();
 
 		// aux button holes
-		translate([-35, 101.5, panel_z/2]) rotate([270, 0, 0]) aux_control_three_button_cluster();
+		translate([-30, 101.5, 0]) rotate([270, 0, 0]) aux_control_three_button_cluster();
-		translate([-35, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
+		translate([-30, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([-72, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
+		translate([-70, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([2, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
+		translate([10, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
 
 		// neutrix button hole
-		translate([frame_center_to_neutrik, (frame_y/2)-neutrik_panel_thickness, panel_z/2])
+		translate([frame_center_to_neutrik, (frame_y/2)-neutrik_panel_thickness, 0])
 			rotate([90, 0, 0]) neutrik_d_mount();
 		translate([frame_center_to_neutrik, (frame_y/2)-neutrik_panel_thickness-4, 0])
 			frame_cutout();

src/frame-middle.scad

@@ -27,14 +27,11 @@ module middle_frame() {
 		mirror([1, 0, 0]) frame_cable_routing_hole();
 
 		// neutrik mounts for connector, switches
-		translate([0, (frame_y/2)-neutrik_panel_thickness, panel_z/2])
+		translate([0, (frame_y/2)-neutrik_panel_thickness, 0]) rotate([90, 0, 0]) neutrik_d_mount();
-			rotate([90, 0, 0]) neutrik_d_mount();
 		translate([0, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([-40, (frame_y/2)-neutrik_panel_thickness, panel_z/2])
+		translate([-40, (frame_y/2)-neutrik_panel_thickness, 0]) rotate([90, 0, 0]) neutrik_d_mount();
-			rotate([90, 0, 0]) neutrik_d_mount();
 		translate([-40, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([40, (frame_y/2)-neutrik_panel_thickness, panel_z/2])
+		translate([40, (frame_y/2)-neutrik_panel_thickness, 0]) rotate([90, 0, 0]) neutrik_d_mount();
-			rotate([90, 0, 0]) neutrik_d_mount();
 		translate([40, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
 	}
 }

src/frame-right.scad

@@ -24,13 +24,13 @@ module right_frame() {
 		mirror([1, 0, 0]) frame_cable_routing_hole();
 
 		// aux button holes
-		translate([35, 101.5, panel_z/2]) rotate([270, 0, 0]) aux_control_three_button_cluster();
+		translate([30, 101.5, 0]) rotate([270, 0, 0]) aux_control_three_button_cluster();
-		translate([35, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
+		translate([30, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([72, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
+		translate([70, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([-2, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
+		translate([-10, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
 
 		// neutrix button hole
-		translate([-frame_center_to_neutrik, (frame_y/2)-neutrik_panel_thickness, panel_z/2])
+		translate([-frame_center_to_neutrik, (frame_y/2)-neutrik_panel_thickness, 0])
 			rotate([90, 0, 0]) neutrik_d_mount();
 		translate([-frame_center_to_neutrik, (frame_y/2)-neutrik_panel_thickness-4, 0])
 			frame_cutout();

src/frame-solo.scad

@@ -11,25 +11,23 @@ module solo_frame() {
 		frame();
 
 		// neutrik mounts for connector, switches
-		translate([0, (frame_y/2)-2.5, panel_z/2]) rotate([90, 0, 0]) neutrik_d_mount();
+		translate([0, (frame_y/2)-2.5, 0]) rotate([90, 0, 0]) neutrik_d_mount();
 		translate([0, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([-40, (frame_y/2)-2.5, panel_z/2]) rotate([90, 0, 0]) neutrik_d_mount();
+		translate([-40, (frame_y/2)-2.5, 0]) rotate([90, 0, 0]) neutrik_d_mount();
 		translate([-40, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
-		translate([40, (frame_y/2)-2.5, panel_z/2]) rotate([90, 0, 0]) neutrik_d_mount();
+		translate([40, (frame_y/2)-2.5, 0]) rotate([90, 0, 0]) neutrik_d_mount();
 		translate([40, (frame_y/2)-neutrik_panel_thickness-4, 0]) frame_cutout();
 
 		// aux button holes
-		translate([-frame_x/2+2.5, 0, panel_z/2]) rotate([90, 0, 270])
+		translate([-frame_x/2+2.5, 0, 0]) rotate([90, 0, 270]) aux_control_three_button_cluster();
-			aux_control_three_button_cluster();
 		translate([(frame_x/2)-neutrik_panel_thickness-4, 0, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([(frame_x/2)-neutrik_panel_thickness-4, -37, 0]) rotate([0, 0, 90]) frame_cutout();
+		translate([(frame_x/2)-neutrik_panel_thickness-4, -40, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([(frame_x/2)-neutrik_panel_thickness-4, 37, 0]) rotate([0, 0, 90]) frame_cutout();
+		translate([(frame_x/2)-neutrik_panel_thickness-4, 40, 0]) rotate([0, 0, 90]) frame_cutout();
 
-		translate([frame_x/2+2.5, 0, panel_z/2]) rotate([90, 0, 270])
+		translate([frame_x/2+2.5, 0, 0]) rotate([90, 0, 270]) aux_control_three_button_cluster();
-			aux_control_three_button_cluster();
 		translate([-(frame_x/2)+neutrik_panel_thickness+4, 0, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([-(frame_x/2)+neutrik_panel_thickness+4, -37, 0]) rotate([0, 0, 90]) frame_cutout();
+		translate([-(frame_x/2)+neutrik_panel_thickness+4, -40, 0]) rotate([0, 0, 90]) frame_cutout();
-		translate([-(frame_x/2)+neutrik_panel_thickness+4, 37, 0]) rotate([0, 0, 90]) frame_cutout();
+		translate([-(frame_x/2)+neutrik_panel_thickness+4, 40, 0]) rotate([0, 0, 90]) frame_cutout();
 	}
 }
 

src/misc-decorative-plate-aux-control-three-button-cluster.scad

@@ -10,8 +10,8 @@ use <misc-neutrik-d-plate.scad>
 module aux_control_three_button_cluster_decorative_plate() {
 	difference() {
 		hull() {
-			translate([-44, 0, 0]) neutrik_d_plate();
+			translate([-50, 0, 0]) neutrik_d_plate();
-			translate([44, 0, 0]) neutrik_d_plate();
+			translate([50, 0, 0]) neutrik_d_plate();
 		}
 		translate([0, 0, -10]) aux_control_three_button_cluster();
 	}