README.md

@@ -17,12 +17,12 @@ Made possible by the amazing efforts of [slagcoin](https://www.slagcoin.com/).
 
 Written by and copyright Brian S. Stephan (<bss@incorporeal.org>).
 
-bullet-system-stick is free software: you can redistribute it and/or modify it under the terms of the GNU General Public
+This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public
 License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later
 version.
 
-bullet-system-stick is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied
+This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied
 warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
 
-You should have received a copy of the GNU General Public License along with bullet-system-stick. If not, see
+You should have received a copy of the GNU General Public License along with this program. If not, see
 <https://www.gnu.org/licenses/>.

TODO.md

@@ -6,13 +6,8 @@ Notes for "next time".
 
 * I need at least 5mm, maybe 10mm, more height, to fit some of my levers like the Nobi Bullet
     * I couldn't even fit a JLF without the compensations in v1 on the bottom panel
-    * I had to bend the pins a bit on Crown SDB-202s, too
 * Top plates are 1-2mm too thick for snap-ins, maybe have a variant with a couple shaved off like with the bottom plate
   workaround
-* The plates bow a bit on the top when pressure is applied, because there's no support from the frame up there ---
-  adding 5mm to the frame should leave a couple mm for support to get added back
-* PCB mount on `top-panel-dir_arc-plus-w-30mm-plus-one-with-mount.scad` doesn't leave room for a USB cable on the right
-  hand side
 * The panels' connection points could probably be a bit thinner to accommodate more bolts. A 20mm bolt barely clears the
   two panels and I don't like that kind of bolt connection.
 * Engraving some cosmetic stuff? Or maybe a place to mount other plates?

src/misc-spdt-neutrik-d-plate.scad

@@ -1,31 +0,0 @@
-/* Copyright Brian Stephan 2023
- *
- * This file is part of bullet-system-stick.
- *
- * bullet-system-stick is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by the
- * Free Software Foundation, either version 3 of the License, or (at your
- * option) any later version.
- *
- * bullet-system-stick is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
- * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * bullet-system-stick. If not, see <https://www.gnu.org/licenses/>.
- */
-
-include <components.scad>
-
-module spdt_neutrik_d_plate() {
-	difference() {
-		cube([30, 35, 2], center=true);
-		translate([9.5, 12, 0]) neutrik_d_screw_hole();
-		translate([-9.5, -12, 0]) neutrik_d_screw_hole();
-		cylinder(r=10+hole_tolerance, h=5, $fn=50, center=true);
-		cube([2.2, 22, 5], center=true);
-	}
-}
-
-spdt_neutrik_d_plate();

src/top-panel-dir_arc-plus-w-30mm-plus-one-with-mount.scad

@@ -1,27 +0,0 @@
-/* Copyright Brian Stephan 2023
- *
- * This file is part of bullet-system-stick.
- *
- * bullet-system-stick is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by the
- * Free Software Foundation, either version 3 of the License, or (at your
- * option) any later version.
- *
- * bullet-system-stick is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
- * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * bullet-system-stick. If not, see <https://www.gnu.org/licenses/>.
- */
-
-include <components.scad>
-use <top-panel-dir_arc-plus-w-30mm-plus-one.scad>
-
-module dir_arc_w_30mm_plus_one_panel_with_mount() {
-	dir_arc_w_30mm_plus_one_panel();
-	translate([65, 55, -(top_plate_z/2) - 3]) pcb_mount();
-}
-
-dir_arc_w_30mm_plus_one_panel_with_mount();

src/top-panel-lever-with-mount.scad

@@ -1,27 +0,0 @@
-/* Copyright Brian Stephan 2023
- *
- * This file is part of bullet-system-stick.
- *
- * bullet-system-stick is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by the
- * Free Software Foundation, either version 3 of the License, or (at your
- * option) any later version.
- *
- * bullet-system-stick is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
- * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * bullet-system-stick. If not, see <https://www.gnu.org/licenses/>.
- */
-
-include <components.scad>
-use <top-panel-lever.scad>
-
-module lever_panel_with_mount() {
-	lever_panel();
-	translate([0, -top_plate_y/2+25, -(top_plate_z/2) - 3]) pcb_mount();
-}
-
-lever_panel_with_mount();

src/top-panel-lever.scad

@@ -33,4 +33,9 @@ module lever_panel() {
 	}
 }
 
-lever_panel();
+module lever_panel_with_mount() {
+	lever_panel();
+	translate([0, -top_plate_y/2+25, -(top_plate_z/2) - 3]) pcb_mount();
+}
+
+lever_panel_with_mount();