document v4.5.0

Signed-off-by: Brian S. Stephan <bss@incorporeal.org>

.gitignore

@@ -1,3 +1,4 @@
 build/
+*.stl
 
 *.sw*

CHANGELOG.md

@@ -2,6 +2,30 @@
 
 Included is a summary of changes to the project, by version. Details can be found in the commit history.
 
+## v4.5.0
+
+### Features
+
+* Many components for the Buildable Stick System - Arcade Edition --- pieces to create a control enclosure for the Qanba
+  2009 base! These pieces live in `extras/bss-ae/` but do use some parts from the base project; check that subdir's
+  README.
+* Created a Sega 2P 11 button layout, basically following the curve of the fourth column and adding a fifth, plus one
+  extra button
+* More decorative plates, this time square ones for an NES-styled project.
+
+### Improvements
+
+* Button layout positions for Sega 2P and directional arc layouts have been parameterized.
+* The decorative plates for the directional arc + W and Sega 2P 9 layout have been split into two files, since there was
+  no reason to keep them as one with multiple pieces anymore.
+* Tweaks to the horizontal stripes in order to get them to print better.
+* Renamed "Sega 2P plus one" to Sega 2P 9, following the pattern of the 11 layout.
+
+### Miscellaneous
+
+* Renaming of extended side pieces to fit the front/back idiom.
+* Cleanups to the demos.
+
 ## v4.4.3
 
 ### Features

demo/all-together-demo-extended-with-windows.scad

@@ -10,10 +10,9 @@ use <frames/pieces/extended/side.scad>
 use <frames/pieces/extended/front-or-back-clean-for-extended-side-aux-and-neutrik.scad>
 use <frames/pieces/extended/front-or-back-clean-for-extended-side-windowed-horiz-stripes.scad>
 use <panels/inset/lever-and-dir_arc-plus-w-30mm-panel.scad>
-use <panels/inset/sega-2p-plus-one-plus-control-panel-with-mount.scad>
+use <panels/inset/sega-2p-nine-plus-control-panel-with-mount.scad>
 use <misc/decorative-plate-24mm-button.scad>
-use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-plus-one.scad>
-use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-plus-one-plates.scad>
+use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-nine.scad>
 use <misc/dustwasher-lsx-nobi.scad>
 
 top_panel_color        = "#5B6579";
@@ -23,7 +22,7 @@ frame_side_color       = "#8E9089";
 top_deco_color         = "#8E9089";
 
 color(top_panel_color) translate([-panel_x/2, 0, frame_z/2-panel_z+0.01]) lever_and_dir_arc_w_30mm_panel();
-color(top_panel_color) translate([panel_x/2, 0, frame_z/2-panel_z+0.01]) sega_2p_plus_one_plus_control_panel_with_mount();
+color(top_panel_color) translate([panel_x/2, 0, frame_z/2-panel_z+0.01]) sega_2p_nine_plus_control_panel_with_mount();
 color(frame_side_color) translate([-frame_x/2+4, 0, -2.5]) extended_left_or_right_frame_piece();
 color(frame_side_color) translate([frame_x/2-4, 0, -2.5]) mirror([1, 0, 0]) extended_left_or_right_frame_piece();
 color(frame_top_bottom_color) translate([-frame_x/2+4, 0, -2.5])  horiz_striped_windowed_front_or_back_box_frame_piece_for_extended_side();
@@ -33,7 +32,7 @@ color(frame_top_bottom_color) translate([frame_x/2-4, 0, -2.5]) rotate([180, 180
 color(bottom_panel_color) translate([-panel_x/2, 0, -5-frame_z/2+5]) panel();
 color(bottom_panel_color) translate([panel_x/2, 0, -5-frame_z/2+5]) panel();
 
-/* color(top_deco_color) translate([0, 0, 3+frame_z/2-4]) dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate_of_plates(); */
-color(top_deco_color) translate([0, 0, 3+frame_z/2-panel_z]) dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate();
+/* color(top_deco_color) translate([0, 0, 3+frame_z/2-4]) dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate_of_plates(); */
+color(top_deco_color) translate([0, 0, 3+frame_z/2-panel_z]) dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate();
 color(top_deco_color) translate([-170, 20, 3+frame_z/2-panel_z]) lsx_nobi_dustwasher();
 color(top_deco_color) translate([panel_x-24, 30, 3+frame_z/2-panel_z]) button_24mm_decorative_plate();

demo/all-together-demo-extended.scad

@@ -6,13 +6,12 @@
 include <parameters.scad>
 include <components.scad>
 use <frames/pieces/extended/front-or-back.scad>
-use <frames/pieces/extended/side-extended-to-bottom.scad>
+use <frames/pieces/extended/side-extended-to-front.scad>
 use <frames/pieces/extended/front-or-back-clean-for-extended-side-aux-and-neutrik.scad>
 use <panels/inset/lever-and-dir_arc-plus-w-30mm-panel.scad>
-use <panels/inset/sega-2p-plus-one-plus-control-panel-with-mount.scad>
+use <panels/inset/sega-2p-nine-plus-control-panel-with-mount.scad>
 use <misc/decorative-plate-24mm-button.scad>
-use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-plus-one.scad>
-use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-plus-one-plates.scad>
+use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-nine.scad>
 use <misc/dustwasher-lsx-nobi.scad>
 
 top_panel_color        = "#5B6579";
@@ -22,7 +21,7 @@ frame_side_color       = "#8E9089";
 top_deco_color         = "#8E9089";
 
 color(top_panel_color) translate([-panel_x/2, 0, frame_z/2-panel_z+0.01]) lever_and_dir_arc_w_30mm_panel();
-color(top_panel_color) translate([panel_x/2, 0, frame_z/2-panel_z+0.01]) sega_2p_plus_one_plus_control_panel_with_mount();
+color(top_panel_color) translate([panel_x/2, 0, frame_z/2-panel_z+0.01]) sega_2p_nine_plus_control_panel_with_mount();
 color(frame_side_color) translate([-frame_x/2+4, 0, -2.5]) extra_extended_left_or_right_frame_piece();
 color(frame_side_color) translate([frame_x/2-4, 0, -2.5]) mirror([1, 0, 0]) extra_extended_left_or_right_frame_piece();
 color(frame_top_bottom_color) translate([-frame_x/2+4, 0, -2.5])  extended_front_or_back_frame_piece();
@@ -32,7 +31,6 @@ color(frame_top_bottom_color) translate([frame_x/2-4, 0, -2.5]) rotate([180, 180
 color(bottom_panel_color) translate([-panel_x/2, 0, -5-frame_z/2+5]) panel();
 color(bottom_panel_color) translate([panel_x/2, 0, -5-frame_z/2+5]) panel();
 
-/* color(top_deco_color) translate([0, 0, 3+frame_z/2-4]) dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate_of_plates(); */
-color(top_deco_color) translate([0, 0, 3+frame_z/2-panel_z]) dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate();
+color(top_deco_color) translate([0, 0, 3+frame_z/2-panel_z]) dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate();
 color(top_deco_color) translate([-170, 20, 3+frame_z/2-panel_z]) lsx_nobi_dustwasher();
 color(top_deco_color) translate([panel_x-24, 30, 3+frame_z/2-panel_z]) button_24mm_decorative_plate();

demo/all-together-demo-solo.scad

@@ -6,7 +6,7 @@
 include <parameters.scad>
 include <components.scad>
 use <frames/pieces/extended/front-or-back.scad>
-use <frames/pieces/extended/side-extended-to-bottom.scad>
+use <frames/pieces/extended/side-extended-to-front.scad>
 use <frames/pieces/extended/front-or-back-clean-for-extended-side-aux-and-neutrik.scad>
 use <panels/inset/lever-and-dir_arc-plus-w-30mm-panel.scad>
 use <panels/inset/lever-and-sega-2p-6-button-panel-with-aux-with-mount.scad>

demo/all-together-demo.scad

@@ -9,10 +9,9 @@ use <frames/pieces/box/side.scad>
 use <frames/pieces/box/front-or-back.scad>
 use <frames/pieces/box/front-or-back-aux-and-neutrik.scad>
 use <panels/inset/lever-and-dir_arc-plus-w-30mm-panel.scad>
-use <panels/inset/sega-2p-plus-one-plus-control-panel-with-mount.scad>
+use <panels/inset/sega-2p-nine-plus-control-panel-with-mount.scad>
 use <misc/decorative-plate-24mm-button.scad>
-use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-plus-one.scad>
-use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-plus-one-plates.scad>
+use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-nine.scad>
 use <misc/dustwasher-lsx-nobi.scad>
 
 panel_color    = "red";
@@ -20,7 +19,7 @@ base_color     = "gray";
 top_deco_color = "white";
 
 color(panel_color) translate([-panel_x/2, 0, frame_z/2-panel_z+0.01]) lever_and_dir_arc_w_30mm_panel();
-color(panel_color) translate([panel_x/2, 0, frame_z/2-panel_z+0.01]) sega_2p_plus_one_plus_control_panel_with_mount();
+color(panel_color) translate([panel_x/2, 0, frame_z/2-panel_z+0.01]) sega_2p_nine_plus_control_panel_with_mount();
 color(base_color) translate([panel_x/2, 0, -2.5]) rotate([0, 180, 0]) side_box_frame_piece();
 color(base_color) translate([-panel_x/2, 0, -2.5]) side_box_frame_piece();
 color(base_color) translate([panel_x/2, 0, -2.5]) front_or_back_box_frame_piece();
@@ -30,6 +29,6 @@ color(base_color) translate([-panel_x/2, 0, -2.5]) rotate([180, 180, 0]) front_o
 color(base_color) translate([-panel_x/2, 0, -5-frame_z/2+5]) panel();
 color(base_color) translate([panel_x/2, 0, -5-frame_z/2+5]) panel();
 
-color(top_deco_color) translate([0, 0, 3+frame_z/2-panel_z]) dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate();
+color(top_deco_color) translate([0, 0, 3+frame_z/2-panel_z]) dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate();
 color(top_deco_color) translate([-170, 20, 3+frame_z/2-panel_z]) lsx_nobi_dustwasher();
 color(top_deco_color) translate([panel_x-24, 30, 3+frame_z/2-panel_z]) button_24mm_decorative_plate();

demo/blown-up-demo.scad

@@ -10,14 +10,14 @@ use <frames/pieces/box/side.scad>
 use <frames/pieces/box/front-or-back.scad>
 use <frames/pieces/box/front-or-back-aux-and-neutrik.scad>
 use <panels/overhang/left-lever-and-dir_arc-plus-w-30mm-panel.scad>
-use <panels/overhang/right-sega-2p-plus-one-plus-control-panel-with-mount.scad>
+use <panels/overhang/right-sega-2p-nine-plus-control-panel-with-mount.scad>
 use <panels/overhang/left-or-right-panel.scad>
 use <misc/decorative-plate-24mm-button.scad>
-use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-plus-one.scad>
+use <misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-nine.scad>
 use <misc/dustwasher-lsx-nobi.scad>
 
 color("#C12E1F") translate([-panel_x/2-25, 0, frame_z/2+75]) lever_and_dir_arc_w_30mm_left_overhang_panel();
-color("#C12E1F") translate([panel_x/2+25, 0, frame_z/2+75]) sega_2p_plus_one_plus_control_right_overhang_panel_with_mount();
+color("#C12E1F") translate([panel_x/2+25, 0, frame_z/2+75]) sega_2p_nine_plus_control_right_overhang_panel_with_mount();
 color("black") translate([-frame_x/2+5-25, -55, -2.5]) front_or_back_box_frame_piece();
 color("black") rotate([0, 180, 0]) translate([-frame_x/2+5-25, -55, -2.5]) front_or_back_box_frame_piece();
 color("black") translate([-frame_x/2+5-50, 0, -2.5]) side_box_frame_piece();
@@ -29,6 +29,6 @@ color("#C12E1F") translate([-panel_x/2-25, 0, -5-frame_z/2-75]) left_or_right_ov
 color("#C12E1F") mirror([0, 1, 0]) translate([panel_x/2+25, 0, -5-frame_z/2-75]) rotate([0, 0, 180])
 	left_or_right_overhang_panel();
 
-color("black") translate([0, 0, 3+frame_z/2+150]) dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate();
+color("black") translate([0, 0, 3+frame_z/2+150]) dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate();
 color("black") translate([-195, 25, 3+frame_z/2+150]) lsx_nobi_dustwasher();
 color("black") translate([panel_x, 25, 3+frame_z/2+150]) button_24mm_decorative_plate();

src/components.scad

@@ -11,6 +11,10 @@ module m4_hole_countersink() {
 	cylinder(r1=m4_bolt_radius, r2=m4_bolt_countersink_radius, h=3.2, $fn=50, center=true);
 }
 
+module m6_hole() {
+	cylinder(r=m6_bolt_radius, h=100, $fn=50, center=true);
+}
+
 module panel_holes() {
 	// holes for mount bolts
 	translate([panel_to_frame_point_x, panel_to_frame_point_y, 0]) m4_hole();
@@ -90,6 +94,12 @@ module aux_control_three_button_cluster() {
 	translate([37, 0, 0]) button_24mm_hole();
 }
 
+module aux_control_three_button_tight_cluster() {
+	translate([-32, 0, 0]) button_24mm_hole();
+	translate([0, 0, 0]) button_24mm_hole();
+	translate([32, 0, 0]) button_24mm_hole();
+}
+
 module m2_mount_post() {
 	difference() {
 		cylinder(r=m2_screw_selftap_radius*2.25, h=3, $fn=6, center=true);
@@ -460,12 +470,18 @@ module sega_2p() {
 	translate([sega_2p_column_4_offset, -19-9, 0]) sega_2p_p1();
 }
 
-module sega_2p_plus_one() {
+module sega_2p_nine() {
 	sega_2p();
 	// just my guesstimate on this one
 	translate([0, -19-9-11-19-9-11, 0]) sega_2p_p1();
 }
 
+module sega_2p_eleven() {
+	sega_2p_nine();
+	translate([sega_2p_column_5_offset, 0, 0]) sega_2p_p1();
+	translate([sega_2p_column_5_offset, -19-9-11, 0]) sega_2p_p1();
+}
+
 module shiokenstar() {
 	translate([-172, 32, 0]) dir_arc_24mm_directionals();
 	sega_2p();

src/extras/bss-ae/README.md

@@ -0,0 +1,38 @@
+# BSS Arcade Edition
+
+Pieces for mounting to a Qanba 2009 in order to create the Buildable Stick System - Arcade Edition.
+
+## Pieces
+
+* 4 `interconnect-x` --- creating the internal support for joining two rows of panels
+* 6 `frames/pieces/interconnect` --- (core project) the standard piece for joining two+ columns of panels
+* 4 `extended-side-no-back` --- the extended side pieces, flush on the back to connect to each other
+* 4 `frames/pieces/extended/front-or-back` --- (core project) the front extended piece
+* 2 `extended-back` --- a small piece that fits into the Qanba 2009 "lip" for running cables
+* 1 `extended-back-left-mount`
+* 1 `extended-back-right-mount` --- extended back pieces that can be mounted to the Qanba 2009 base
+* 1 `panel-front-left-mount`
+* 1 `panel-front-right-mount` --- blank panels that can be mounted to the Qanba 2009 base
+* 6 `panels/inset/panel` --- the rest of the bottom panels
+* 4 `panels/inset/` panels of your choice for the front controls
+* 2 `panel-three-aux-buttons` --- for aux controls in the back row
+* 2 `panel-three-aux-buttons-and-rocker-hole` --- for aux controls and the wired rocker in the back row
+* 4 `decorative-plate-aux-control-tight-three-button-cluster` --- for decorating the aux control clusters
+* 4 `src/misc/` decorative plates of your choice for the front controls, and similar miscellany
+* 4 `mount-spacer` --- making a flush mount between the enclosure and the base
+
+## Hardware
+
+* 32 45mm M4 hex brass standoffs (or equivalent) for each panel/frame compartment
+* 64 8-12mm M4 countersunk hex bolts for attaching panels to the compartments
+* 4 8-12mm M3 hex bolts and 4 M3 flange nuts for attaching rocker switches to the back panels
+* 4 40mm M6 bolts for connecting the enclosure to the base
+* 4 M6 flange nuts
+
+## Components
+
+* 2 controller boards, e.g. the RP2040 Advanced Breakout Board
+* buttons and/or levers as desired
+* necessary wiring
+
+For the rest of the build (e.g. mounting a level to a panel), see the core README.

src/extras/bss-ae/decorative-plate-aux-control-tight-three-button-cluster.scad

@@ -0,0 +1,24 @@
+/* Decorative plate for aux buttons.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+decorative_radius_scale = 1.5;
+jumbo_decorative_radius_scale = 0;
+include <components.scad>
+
+module aux_control_three_button_tight_cluster_decorative_plate() {
+	difference() {
+		// get a 2mm slice of the bigger button cylinders
+		translate([0, 0, -25]) hull() aux_control_three_button_tight_cluster();
+		// keep a thin slice
+		translate([0, 0, -100]) cube([500, 500, 198], center=true);
+		translate([0, 0, 100]) cube([500, 500, 198], center=true);
+		// cut out the normal holes
+		translate([0, 0, -1]) aux_control_three_button_tight_cluster();
+	}
+}
+
+aux_control_three_button_tight_cluster_decorative_plate();

src/extras/bss-ae/extended-back-left-mount.scad

@@ -0,0 +1,26 @@
+/* A back piece of the enclosure, with a mounting hole.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <extended-back.scad>
+
+// X: inner post to post (inclusive) is approx. 428.625mm, so half that, minus half the post itself
+// (41.28mm) is how much in from a normal panel to put the M6 mounting hole
+// Y: eyeballed it to 30mm
+mount_hole_x = (panel_x / 2) - (panel_x - ((428.625 / 2) - (41.28 / 2)));
+mount_hole_y = (panel_y / 2) + 30;
+
+module left_mount_extended_back() {
+	difference() {
+		extended_back();
+		translate([mount_hole_x, -mount_hole_y, -30]) m6_hole();
+		// punch out the back for cables
+		cube([frame_x-70, frame_y+160, frame_z-20], center=true);
+	}
+}
+
+left_mount_extended_back();

src/extras/bss-ae/extended-back-right-mount.scad

@@ -0,0 +1,15 @@
+/* A back piece of the enclosure, with a mounting hole.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <extended-back-left-mount.scad>
+
+module right_mount_extended_back() {
+	mirror([1, 0, 0]) left_mount_extended_back();
+}
+
+right_mount_extended_back();

src/extras/bss-ae/extended-back.scad

@@ -0,0 +1,30 @@
+/* A back piece extended the rest of the depth of the base.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <frames/pieces/extended/front-or-back.scad>
+
+module back_piece_extension() {
+	// combine the original wall with a copy to "pull" the wall out
+	hull() {
+		linear_extrude(height=80) bottom_piece_wall();
+		linear_extrude(height=(frame_wall-frame_bevel_height)) bottom_piece_wall();
+	}
+}
+
+module extended_back() {
+	difference() {
+		union() {
+			clean_front_or_back();
+			translate([0, -frame_y/2+frame_wall, 0]) rotate([90, 0, 0]) back_piece_extension();
+		}
+		cube([frame_x-60, frame_y+160-10, frame_z-10], center=true);
+		translate([0, -frame_y/2-35, 0]) cube([frame_x-20, 70, frame_z-10], center=true);
+	}
+}
+
+extended_back();

src/extras/bss-ae/extended-side-no-back.scad

@@ -0,0 +1,60 @@
+/* Create an extended side that is flush on the back to lay against another side.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <frames/complete/left-frame.scad>
+use <frames/pieces/box/side.scad>
+use <frames/pieces/extended/front-or-back.scad>
+
+module side_frame_piece_wall() {
+	// this doesn't use the side_frame_piece because of the 45 degree angle geometry
+	// not creating a clean thing to cut, so we just take the whole wall and use that
+	projection(cut=true) rotate([0, 90, 0]) translate([frame_x/2-frame_wall-(frame_bevel_height/2), 0, 0])
+		left_frame();
+}
+
+module side_and_bottom_frame_piece_wall() {
+	// get a slice of the pieces, to use it in extruding
+	// this doesn't use the side_frame_piece because of the 45 degree angle geometry
+	// not creating a clean thing to cut, so we just take the whole wall and use that
+	side_frame_piece_wall();
+	projection(cut=true) translate([0, -frame_y/2+frame_wall, 0]) rotate([90, 90, 0]) bottom_piece_extension();
+}
+
+module side_and_bottom_frame_piece_extension() {
+	// combine the original with a shrunken piece to "pull" the wall out
+	hull() {
+		linear_extrude(height=frame_extension_y) scale([0.5, 0.90, 1]) side_and_bottom_frame_piece_wall();
+		linear_extrude(height=frame_extension_y) scale([0.5, 1, 1])
+			difference() {
+				side_frame_piece_wall();
+				// remove the front piece so it doesn't interfere with the front extend
+				translate([0, -frame_y/2, 0]) square([frame_x, frame_y], center=true);
+			}
+		linear_extrude(height=frame_bevel_height) side_and_bottom_frame_piece_wall();
+	}
+}
+
+module extra_extended_left_or_right_frame_piece() {
+	difference() {
+		union() {
+			difference() {
+				side_box_frame_piece();
+				// chop off the old edge which is getting replaced with the extension
+				translate([-frame_x/2+frame_bevel_height/2, 0, 0])
+					cube([frame_bevel_height, frame_y, frame_z], center=true);
+			}
+			translate([-frame_x/2+frame_bevel_height*2, 0, 0])
+				rotate([0, -90, 0]) side_and_bottom_frame_piece_extension();
+		}
+		// minus the back piece where the wall would be, since there is no wall and the pieces and panels
+		// go flush against one another
+		translate([0, frame_y/2-(frame_wall/2), 0]) cube([frame_x*2, frame_wall, frame_z], center=true);
+	}
+}
+
+extra_extended_left_or_right_frame_piece();

src/extras/bss-ae/interconnect-x.scad

@@ -0,0 +1,30 @@
+/* Interconnect frames along the x-axis (the longer side)
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <frames/pieces/box/front-or-back.scad>
+
+module interconnect_frame_half_piece() {
+	translate([0, frame_y/2-frame_wall, 0]) difference() {
+		front_or_back_box_frame_piece();
+		translate([0, (-frame_y+frame_wall)/2-panel_overhang_amount, 0])
+			cube([overhang_panel_x, frame_wall+panel_overhang_amount*2, frame_z], center=true);
+	}
+}
+
+module interconnect_frame_piece() {
+	difference() {
+		union() {
+			// slight translate is to make this a 2-manifold in OpenSCAD
+			translate([0, -0.01, 0]) interconnect_frame_half_piece();
+			mirror([0, 1, 0]) interconnect_frame_half_piece();
+		}
+		rotate([0, 0, 90]) translate([-frame_y/2, 0, 0]) frame_cable_routing_hole();
+	}
+}
+
+interconnect_frame_piece();

src/extras/bss-ae/mount-spacer.scad

@@ -0,0 +1,17 @@
+/* Just a simple washer to go between the frame post and the arcade enclosure.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+
+module mount_spacer() {
+	difference() {
+		cylinder(r=25, h=1.25, $fn=50, center=true);
+		m6_hole();
+	}
+}
+
+mount_spacer();

src/extras/bss-ae/panel-front-left-mount.scad

@@ -0,0 +1,24 @@
+/* A panel with a mount point for the front left of the enclosure.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <panels/inset/panel.scad>
+
+// X: inner post to post (inclusive) is approx. 428.625mm, so half that, minus half the post itself
+// (41.28mm) is how much in from a normal panel to put the M6 mounting hole
+// Y: eyeballed it to 2": 50.80mm
+mount_hole_x = (panel_x / 2) - (panel_x - ((428.625 / 2) - (41.28 / 2)));
+mount_hole_y = (panel_y / 2) - 50.80;
+
+module front_left_mount_panel() {
+	difference() {
+		panel();
+		translate([-mount_hole_x, -mount_hole_y, 0]) m6_hole();
+	}
+}
+
+front_left_mount_panel();

src/extras/bss-ae/panel-front-right-mount.scad

@@ -0,0 +1,14 @@
+/*
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <panel-front-left-mount.scad>
+
+module front_right_mount_panel() {
+	mirror([1, 0, 0]) front_left_mount_panel();
+}
+
+front_right_mount_panel();

src/extras/bss-ae/panel-three-aux-buttons-and-rocker-hole.scad

@@ -0,0 +1,18 @@
+/* A panel for mounting a couple aux buttons in a out of the way spot.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+
+module three_aux_button_and_20mm_panel() {
+	difference() {
+		panel();
+		translate([0, -70, 0]) aux_control_three_button_tight_cluster();
+		translate([0, frame_y/2-30, 0]) rotate([180, 0, 0]) neutrik_d_mount();
+	}
+}
+
+three_aux_button_and_20mm_panel();

src/extras/bss-ae/panel-three-aux-buttons.scad

@@ -0,0 +1,17 @@
+/* A panel for mounting a couple aux buttons in a out of the way spot.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+
+module three_aux_button_panel() {
+	difference() {
+		panel();
+		translate([0, -70, 0]) aux_control_three_button_tight_cluster();
+	}
+}
+
+three_aux_button_panel();

src/frames/pieces/box/front-or-back-windowed-horiz-stripes.scad

@@ -16,12 +16,11 @@ module horiz_striped_windowed_front_or_back_box_frame_piece() {
 	difference() {
 		front_or_back_box_frame_piece();
 		// subtract frame wall windows
-		translate([0, -(frame_y-frame_wall)/2, 17.5]) front_stripe();
-		translate([0, -(frame_y-frame_wall)/2, 10.5]) front_stripe();
-		translate([0, -(frame_y-frame_wall)/2, 3.5]) front_stripe();
-		translate([0, -(frame_y-frame_wall)/2, -3.5]) front_stripe();
-		translate([0, -(frame_y-frame_wall)/2, -10.5]) front_stripe();
-		translate([0, -(frame_y-frame_wall)/2, -17.5]) front_stripe();
+		translate([0, -(frame_y-frame_wall)/2, 18]) front_stripe();
+		translate([0, -(frame_y-frame_wall)/2, 9]) front_stripe();
+		translate([0, -(frame_y-frame_wall)/2, 0]) front_stripe();
+		translate([0, -(frame_y-frame_wall)/2, -9]) front_stripe();
+		translate([0, -(frame_y-frame_wall)/2, -18]) front_stripe();
 		// subtract the inner wall area that will be provided by the other piece
 		front_or_back_inner_wall_frame_piece();
 	}

src/frames/pieces/box/side-windowed-horiz-stripes.scad

@@ -16,12 +16,11 @@ module horiz_striped_windowed_side_box_frame_piece() {
 	difference() {
 		side_box_frame_piece();
 		// subtract frame wall windows
-		translate([-(frame_x-frame_wall)/2, 0, 17.5]) side_stripe();
-		translate([-(frame_x-frame_wall)/2, 0, 10.5]) side_stripe();
-		translate([-(frame_x-frame_wall)/2, 0, 3.5]) side_stripe();
-		translate([-(frame_x-frame_wall)/2, 0, -3.5]) side_stripe();
-		translate([-(frame_x-frame_wall)/2, 0, -10.5]) side_stripe();
-		translate([-(frame_x-frame_wall)/2, 0, -17.5]) side_stripe();
+		translate([-(frame_x-frame_wall)/2, 0, 18]) side_stripe();
+		translate([-(frame_x-frame_wall)/2, 0, 9]) side_stripe();
+		translate([-(frame_x-frame_wall)/2, 0, 0]) side_stripe();
+		translate([-(frame_x-frame_wall)/2, 0, -9]) side_stripe();
+		translate([-(frame_x-frame_wall)/2, 0, -18]) side_stripe();
 		// subtract the inner wall area that will be provided by the other piece
 		side_inner_wall_frame_piece();
 	}

src/misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-nine-rectangles.scad

@@ -8,7 +8,7 @@ decorative_radius_scale = 1.5;
 jumbo_decorative_radius_scale = 0;
 include <components.scad>
 
-module dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate_of_plates() {
+module dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate_of_plates() {
 	difference() {
 		// layout offset + 30 = width for layout plus button width + 12+3 = space around button
 		left_plate_x = dir_arc_30mm_column_3_offset + 30 + 12;
@@ -29,8 +29,8 @@ module dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate_of_plates() {
 		}
 		// cut out the normal holes
 		translate([-panel_x/2, 0, -1]) dir_arc_w_30mm();
-		translate([panel_x/2, 0, -1]) sega_2p_plus_one();
+		translate([panel_x/2, 0, -1]) sega_2p_nine();
 	}
 }
 
-dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate_of_plates();
+dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate_of_plates();

src/misc/decorative-plate-dir_arc-plus-w-30mm-and-sega-2p-nine.scad

@@ -6,19 +6,19 @@
 include <parameters.scad>
 include <components.scad>
 
-module dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate() {
+module dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate() {
 	difference() {
 		// get a 2mm slice of the bigger button cylinders
 		union() {
 			translate([-panel_x/2, 0, -65]) dir_arc_w_30mm();
-			translate([panel_x/2, 0, -65]) sega_2p_plus_one();
+			translate([panel_x/2, 0, -65]) sega_2p_nine();
 		}
 		translate([0, 0, -100]) cube([500, 500, 198], center=true);
 		translate([0, 0, 100]) cube([500, 500, 198], center=true);
 		// cut out the normal holes
 		translate([-panel_x/2, 0, -1]) dir_arc_w_30mm();
-		translate([panel_x/2, 0, -1]) sega_2p_plus_one();
+		translate([panel_x/2, 0, -1]) sega_2p_nine();
 	}
 }
 
-dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate();
+dir_arc_plus_w_30mm_and_sega_2p_nine_decorative_plate();

src/misc/decorative-plate-dir_arc-plus-w-30mm-plate.scad

@@ -1,4 +1,5 @@
-/*
+/* Decorative plate for directional buttons.
+ *
  * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
  * SPDX-License-Identifier: GPL-3.0-or-later
  */
@@ -8,19 +9,15 @@ decorative_radius_scale = 1.5;
 jumbo_decorative_radius_scale = 0;
 include <components.scad>
 
-module dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate_of_plates() {
+module dir_arc_plus_w_30mm_plate_decorative_plate() {
 	difference() {
 		// get a 2mm slice of the bigger button cylinders
-		union() {
-			translate([-panel_x/2, 0, -25]) hull() dir_arc_w_30mm();
-			translate([panel_x/2, 0, -25]) hull() sega_2p_plus_one();
-		}
+		translate([-panel_x/2, 0, -25]) hull() dir_arc_w_30mm();
 		translate([0, 0, -100]) cube([500, 500, 198], center=true);
 		translate([0, 0, 100]) cube([500, 500, 198], center=true);
 		// cut out the normal holes
 		translate([-panel_x/2, 0, -1]) dir_arc_w_30mm();
-		translate([panel_x/2, 0, -1]) sega_2p_plus_one();
 	}
 }
 
-dir_arc_plus_w_30mm_and_sega_2p_plus_one_decorative_plate_of_plates();
+dir_arc_plus_w_30mm_plate_decorative_plate();

src/misc/decorative-plate-sega-2p-eleven-plate.scad

@@ -0,0 +1,23 @@
+/* Decorative plate for directional buttons.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+decorative_radius_scale = 1.5;
+jumbo_decorative_radius_scale = 0;
+include <components.scad>
+
+module sega_2p_eleven_plate_decorative_plate() {
+	difference() {
+		// get a 2mm slice of the bigger button cylinders
+		translate([panel_x/2, 0, -25]) hull() sega_2p_eleven();
+		translate([0, 0, -100]) cube([500, 500, 198], center=true);
+		translate([0, 0, 100]) cube([500, 500, 198], center=true);
+		// cut out the normal holes
+		translate([panel_x/2, 0, -1]) sega_2p_eleven();
+	}
+}
+
+sega_2p_eleven_plate_decorative_plate();

src/misc/decorative-plate-sega-2p-nine-plate.scad

@@ -0,0 +1,25 @@
+/* A rounded corner decorative plate for the Sega 2P + 1 button layout.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+decorative_radius_scale = 1.5;
+jumbo_decorative_radius_scale = 0;
+include <components.scad>
+
+module sega_2p_nine_decorative_plate_of_plates() {
+	difference() {
+		// get a 2mm slice of the bigger button cylinders
+		union() {
+			translate([panel_x/2, 0, -25]) hull() sega_2p_nine();
+		}
+		translate([0, 0, -100]) cube([500, 500, 198], center=true);
+		translate([0, 0, 100]) cube([500, 500, 198], center=true);
+		// cut out the normal holes
+		translate([panel_x/2, 0, -1]) sega_2p_nine();
+	}
+}
+
+sega_2p_nine_decorative_plate_of_plates();

src/misc/decorative-plate-sega-2p-nine.scad

@@ -6,15 +6,15 @@
 include <parameters.scad>
 include <components.scad>
 
-module sega_2p_plus_one_decorative_plate() {
+module sega_2p_nine_decorative_plate() {
 	difference() {
 		// get a 2mm slice of the bigger button cylinders
-		translate([0, 0, -55]) sega_2p_plus_one();
+		translate([0, 0, -55]) sega_2p_nine();
 		translate([0, 0, -100]) cube([500, 500, 198], center=true);
 		translate([0, 0, 100]) cube([500, 500, 198], center=true);
 		// cut out the normal holes
-		translate([0, 0, -1]) sega_2p_plus_one();
+		translate([0, 0, -1]) sega_2p_nine();
 	}
 }
 
-sega_2p_plus_one_decorative_plate();
+sega_2p_nine_decorative_plate();

src/panels/inset/sega-2p-eleven-panel-with-mount.scad

@@ -0,0 +1,16 @@
+/* 11-button Sega 2P panel with PCB mount
+ *
+ * SPDX-FileCopyrightText: © 2023 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <sega-2p-eleven-panel.scad>
+
+module sega_2p_eleven_panel_with_mount() {
+	sega_2p_eleven_panel();
+	translate([30, -50, -(panel_z/2) - 3]) pcb_mount();
+}
+
+sega_2p_eleven_panel_with_mount();

src/panels/inset/sega-2p-eleven-panel.scad

@@ -0,0 +1,17 @@
+/* A panel with the Sega 2P button layout plus three extra buttons for whatever purpose.
+ *
+ * SPDX-FileCopyrightText: © 2024 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+
+module sega_2p_eleven_panel() {
+	difference() {
+		panel();
+		sega_2p_eleven();
+	}
+}
+
+sega_2p_eleven_panel();

src/panels/inset/sega-2p-nine-panel.scad

@@ -6,11 +6,11 @@
 include <parameters.scad>
 include <components.scad>
 
-module sega_2p_plus_one_panel() {
+module sega_2p_nine_panel() {
 	difference() {
 		panel();
-		sega_2p_plus_one();
+		sega_2p_nine();
 	}
 }
 
-sega_2p_plus_one_panel();
+sega_2p_nine_panel();

src/panels/inset/sega-2p-nine-plus-control-panel-with-mount.scad

@@ -5,11 +5,11 @@
 
 include <parameters.scad>
 include <components.scad>
-use <right-sega-2p-plus-one-panel.scad>
+use <sega-2p-nine-plus-control-panel.scad>
 
-module sega_2p_plus_one_with_mount_right_overhang_panel() {
-	sega_2p_plus_one_right_overhang_panel();
+module sega_2p_nine_plus_control_panel_with_mount() {
+	sega_2p_nine_plus_control_panel();
 	translate([30, -50, -(panel_z/2) - 3]) pcb_mount();
 }
 
-sega_2p_plus_one_with_mount_right_overhang_panel();
+sega_2p_nine_plus_control_panel_with_mount();

src/panels/inset/sega-2p-nine-plus-control-panel.scad

@@ -6,13 +6,13 @@
 include <parameters.scad>
 include <components.scad>
 
-module sega_2p_plus_one_plus_control_panel() {
+module sega_2p_nine_plus_control_panel() {
 	difference() {
 		panel();
-		sega_2p_plus_one();
+		sega_2p_nine();
 		rotate([0, 0, 180]) side_chopper();
 		translate([89, 30, 0]) button_24mm_hole();
 	}
 }
 
-sega_2p_plus_one_plus_control_panel();
+sega_2p_nine_plus_control_panel();

src/panels/overhang/right-sega-2p-nine-control-panel-with-mount-with-oled.scad

@@ -5,14 +5,14 @@
 
 include <parameters.scad>
 include <components.scad>
-use <right-sega-2p-plus-one-plus-control-panel-with-mount.scad>
+use <right-sega-2p-nine-plus-control-panel-with-mount.scad>
 
-module sega_2p_plus_one_plus_control_right_overhang_panel_with_mount_with_oled() {
+module sega_2p_nine_plus_control_right_overhang_panel_with_mount_with_oled() {
 	difference() {
-		sega_2p_plus_one_plus_control_right_overhang_panel_with_mount();
+		sega_2p_nine_plus_control_right_overhang_panel_with_mount();
 		translate([75, 77.5, 0]) oled_ssd1306_mount_cutout();
 	}
 	translate([75, 77.5, 0.5]) oled_ssd1306_mount();
 }
 
-sega_2p_plus_one_plus_control_right_overhang_panel_with_mount_with_oled();
+sega_2p_nine_plus_control_right_overhang_panel_with_mount_with_oled();

src/panels/overhang/right-sega-2p-nine-panel-with-mount.scad

@@ -5,11 +5,11 @@
 
 include <parameters.scad>
 include <components.scad>
-use <sega-2p-plus-one-plus-control-panel.scad>
+use <right-sega-2p-nine-panel.scad>
 
-module sega_2p_plus_one_plus_control_panel_with_mount() {
-	sega_2p_plus_one_plus_control_panel();
+module sega_2p_nine_with_mount_right_overhang_panel() {
+	sega_2p_nine_right_overhang_panel();
 	translate([30, -50, -(panel_z/2) - 3]) pcb_mount();
 }
 
-sega_2p_plus_one_plus_control_panel_with_mount();
+sega_2p_nine_with_mount_right_overhang_panel();

src/panels/overhang/right-sega-2p-nine-panel.scad

@@ -6,12 +6,12 @@
 include <parameters.scad>
 include <components.scad>
 
-module sega_2p_plus_one_right_overhang_panel() {
+module sega_2p_nine_right_overhang_panel() {
 	difference() {
 		panel_with_raised_overhang();
-		sega_2p_plus_one();
+		sega_2p_nine();
 		rotate([0, 0, 180]) side_chopper();
 	}
 }
 
-sega_2p_plus_one_right_overhang_panel();
+sega_2p_nine_right_overhang_panel();

src/panels/overhang/right-sega-2p-nine-plus-control-panel-with-mount.scad

@@ -0,0 +1,15 @@
+/*
+ * SPDX-FileCopyrightText: © 2023 Brian S. Stephan <bss@incorporeal.org>
+ * SPDX-License-Identifier: GPL-3.0-or-later
+ */
+
+include <parameters.scad>
+include <components.scad>
+use <right-sega-2p-nine-plus-control-panel.scad>
+
+module sega_2p_nine_plus_control_right_overhang_panel_with_mount() {
+	sega_2p_nine_plus_control_right_overhang_panel();
+	translate([30, -50, -(panel_z/2) - 3]) pcb_mount();
+}
+
+sega_2p_nine_plus_control_right_overhang_panel_with_mount();

src/panels/overhang/right-sega-2p-nine-plus-control-panel.scad

@@ -6,13 +6,13 @@
 include <parameters.scad>
 include <components.scad>
 
-module sega_2p_plus_one_plus_control_right_overhang_panel() {
+module sega_2p_nine_plus_control_right_overhang_panel() {
 	difference() {
 		panel_with_raised_overhang();
-		sega_2p_plus_one();
+		sega_2p_nine();
 		rotate([0, 0, 180]) side_chopper();
 		translate([89, 30, 0]) button_24mm_hole();
 	}
 }
 
-sega_2p_plus_one_plus_control_right_overhang_panel();
+sega_2p_nine_plus_control_right_overhang_panel();

src/panels/overhang/right-sega-2p-plus-one-plus-control-panel-with-mount.scad

@@ -1,15 +0,0 @@
-/*
- * SPDX-FileCopyrightText: © 2023 Brian S. Stephan <bss@incorporeal.org>
- * SPDX-License-Identifier: GPL-3.0-or-later
- */
-
-include <parameters.scad>
-include <components.scad>
-use <right-sega-2p-plus-one-plus-control-panel.scad>
-
-module sega_2p_plus_one_plus_control_right_overhang_panel_with_mount() {
-	sega_2p_plus_one_plus_control_right_overhang_panel();
-	translate([30, -50, -(panel_z/2) - 3]) pcb_mount();
-}
-
-sega_2p_plus_one_plus_control_right_overhang_panel_with_mount();

src/parameters.scad

@@ -17,6 +17,9 @@ m4_bolt_radius = 2 + hole_tolerance;
 m4_bolt_countersink_radius = 6.1 + hole_tolerance;
 m4_bolt_hex_exterior_radius = 3.6 + hole_tolerance;
 
+// M6
+m6_bolt_radius = 3 + hole_tolerance;
+
 // 24mm button
 small_button_radius = 12 + hole_tolerance;
 
@@ -111,6 +114,7 @@ slash_height = frame_z-panel_z*3;
 sega_2p_column_2_offset = 30.5;
 sega_2p_column_3_offset = sega_2p_column_2_offset + 36;
 sega_2p_column_4_offset = sega_2p_column_3_offset + 36;
+sega_2p_column_5_offset = sega_2p_column_4_offset + 36;
 
 // this offset is from the left edge of the panel
 sega_2p_column_1_left_panel_edge_offset = 28.06;